• Skip to main content
  • Skip to primary sidebar
  • Skip to footer

Turnkey Dental Supplies

Premium Dental Equipment

  • Home
  • About Us
  • Shop
    • All Products
    • My account
    • Cart
    • Checkout
  • Our Services
    • Dental Practice Design & Surgery Layouts for Modern Surgeries
    • Dental Practice Build & Installation Services in the UK
    • Reliable Dental Practice maintenance and support
    • Dental Practice & Surgery Equipment
    • Squat Dental Practices
  • Case Studies
  • Product Brochures
  • Blog Posts
  • Contact Us

Dental Machine Maintenance

Dental X-Ray Machine Parts: What They Do, What Goes Wrong, and When to Replace Them 

An image that’s suddenly grainier than it should be, an arm that won’t hold its position without drifting, a unit that trips the moment it’s switched on. Faults like these almost always trace back to one of a small number of components, and knowing which one saves a lot of guesswork before an engineer even arrives.

Between installing X-ray systems and maintaining them once they’re in daily use, the pattern of failures and when they occur becomes fairly predictable. Below is what each core part does, the failure signs worth recognising, what UK compliance requires around ageing equipment, and how to weigh up repair against replacement when a fault turns out to be more than a quick fix.

The core components of dental X-ray machine parts and where they can fail

Most intraoral units share the same basic architecture regardless of manufacturer. Panoramic and CBCT systems add a rotating column and detector, but the underlying components are the same ones doing the work. 

ComponentFunctionSign of failure
Control panel Houses the exposure settings (kV, mA, timer) and the on/off circuitry Unit won’t power on, trips on exposure, or gives inconsistent exposure readings 
Extension arm Suspends and positions the tubehead, carries the wiring between panel and tubehead Drift, sagging, or failure to hold position once released 
Tubehead (tube, collimator, PID) Generates the X-ray beam and shapes it before it reaches the patient Inconsistent exposure, unusual noise on firing, or visible wear around the PID seal 
Sensor or phosphor plate Captures the image (solid-state sensor for direct digital, phosphor plate for CR systems) Streaking, dead pixels, patchy images, or a sensor that intermittently drops connection 
Rotating column and detector (panoramic/CBCT only) Drives the orbital movement around the patient and captures the wider-field image Uneven panoramic images, motor noise, or the arm stalling mid-cycle 

The sensor or phosphor plate is worth calling out separately from the tubehead, since it’s the component most practices interact with daily and the one most likely to show wear from routine handling rather than age alone. It’s also the part we get asked about most often when a practice is deciding whether to repair what they have or move to a newer digital system. 

What Each Fault Usually Means

A given fault indicator doesn’t always point to a single cause, but most issues cluster around a handful of likely explanations worth checking before booking an engineer. 

Image streaking or dead pixels

Usually the sensor or phosphor plate rather than the tubhead. Cable damage on wired sensors produces a similar effect and is worth ruling out first, as this is a cheaper fix. 

Arm won’t hold position. 

Points to the extension arm’s counterbalance mechanism losing tension, particularly on older units where the balancing spring or friction joint has worn. 

Unit won’t power on or trips repeatedly.

Control panel or electrical supply issue. Worth checking the practice’s own circuit before assuming the unit itself has failed. 

Inconsistent exposure across shots

Tube ageing is the common cause on older units, though a failing collimator can produce similar inconsistency. 

Unusual noise on firing

Worth flagging early. Mechanical noise from the tubehead often precedes a more serious failure rather than resolving on its own

None of these confirms the cause on their own. What they do is narrow down what an engineer needs to check first, which shortens the callout, and it’s exactly this kind of triage our maintenance and support team works through with practices before deciding what’s needed.

Compliance and Servicing Obligations for UK Practices

Dental X-ray equipment sits under two overlapping pieces of UK legislation. The Ionising Radiations Regulations 2017 (IRR17) govern occupational exposure and require routine quality assurance of the equipment itself. The Ionising Radiation (Medical Exposure) Regulations 2017 (IR(ME)R) cover exposure to patients and include a requirement for critical examination of new or substantially altered equipment before it’s used clinically.

In practice, this means two things for a practice weighing up a fault. First, servicing and QA records need to be maintained and available, since CQC inspections routinely ask to see them. Second, any replacement unit needs to be tested and commissioned before it goes into clinical use, not simply installed and switched on, which is standard on every system we supply and fit.

A repaired unit generally continues under its existing QA schedule. A new unit resets that process, which has a bearing on how quickly it can go into use and is worth factoring into the timeline as much as the cost.

Repair or Replace? A Decision Framework

The right call depends on more than the immediate repair quote. A few factors are worth weighing together rather than in isolation.

Age against typical service life 

Digital sensors and phosphor plates generally have a shorter practical lifespan than the tubehead or extension arm, so a five-year-old sensor failing isn’t unusual, while a five-year-old tubehead failing is worth investigating further. 

Repair cost as a proportion of a new unit 

A repair quote approaching a third or more of a replacement unit’s cost is usually the point where replacement starts to make more sense, particularly if the unit is already past its expected service life. 

Downtime tolerance. 

 A single-surgery practice with no backup imaging has less room to wait on a parts order than a multi-surgery practice that can redirect patients temporarily. 

Upgrade opportunity 

A phosphor plate or older sensor failure is often the natural point to move to a newer digital system, since the cost difference between repairing an ageing component and moving to current imaging technology is sometimes smaller than expected. 

Taken together, these usually make the decision fairly clear before a quote is even requested, and it’s a conversation worth having with a supplier before committing to either route. 

Choosing and Maintaining X-Ray Equipment with Turnkey Dental

Turnkey Dental has over 52 years of combined experience supplying and installing dental equipment across the UK, and we’re the exclusive UK supplier and installer of Owandy dental X-ray systems, covering CR, panoramic, cephalometric, CBCT, and intraoral sensor units.

Every unit we supply is professionally installed, tested, and commissioned before handover, which covers the compliance step outlined above as part of the installation rather than as a separate task. If a fault turns out to be a maintenance issue rather than a case for replacement, our ongoing support and maintenance service covers diagnosis and repair without needing to go through a full procurement process, and if it’s time for something newer, we’ll talk through what fits your surgery rather than pushing the largest system on the range.

Whichever side of the repair-or-replace decision a fault lands on, the starting point is the same conversation. Get in touch, and we’ll help you work out which one you’re dealing with.

Dental X-ray machine parts Frequently Asked Questions

How long do dental X-ray machines last?

Tubeheads and extension arms typically run for well over a decade with routine servicing. Digital sensors and phosphor plates tend to have a shorter practical lifespan, often five to eight years depending on handling and daily use.

Can a dental X-ray sensor be repaired?

Some faults, particularly cable damage on wired sensors, can be repaired. Internal sensor failures are usually not economical to repair given the cost relative to a replacement sensor.

How often should a dental X-ray machine be serviced?

Routine quality assurance checks are required under IRR17, with frequency depending on the type of equipment and the practice’s local rules. Manufacturer-recommended service intervals sit alongside these statutory checks.

Is it cheaper to repair or replace a dental X-ray unit?

It depends on the fault, the age of the unit, and the proportion of a new unit’s cost the repair represents. A repair on a unit already near the end of its expected service life rarely represents good value compared with replacement, and it’s worth getting a straight answer on that from whoever quotes the repair.H3: Can a dental X-ray sensor be repaired?

Some faults, particularly cable damage on wired sensors, can be repaired. Internal sensor failures are usually not economical to repair given the cost relative to a replacement sensor.

How often should a dental X-ray machine be serviced?

Routine quality assurance checks are required under IRR17, with frequency depending on the type of equipment and the practice’s local rules. Manufacturer-recommended service intervals sit alongside these statutory checks.

Is it cheaper to repair or replace a dental X-ray unit?

It depends on the fault, the age of the unit, and the proportion of a new unit’s cost the repair represents. A repair on a unit already near the end of its expected service life rarely represents good value compared with replacement, and it’s worth getting a straight answer on that from whoever quotes the repair.

Primary Sidebar

Product categories

  • Dental Compressors
  • Dental Equipment Parts
  • Dental Practice Autoclaves
  • Dental Practice Consumables
  • Dental Stools for Dentists
  • Dental Suction Units
  • Dental X-Ray Equipment
  • High-Quality Dental Camera
  • High-Quality Dental Handpieces
  • Oral Scanners for Dentists
  • Premium Dental Chairs for Your Practice

Recent Posts

  • Dental surgery cabinetry: a practical design guide
  • How to Choose the Right Dental Camera for Your Practice Installation
  • Why Ergonomic Dental Seating Is Essential for Modern Practice
  • How Will the UDA Reforms Affect Your Practice?
  • What No One Tells You About Opening a Squat Dental Practice

Contact Us

Turnkey Dental Supplies Ltd
Correspondence office:
15 Queen Square 8192
Leeds, West Yorkshire,
LS2 8AJ

Call:
07827 669302 or 0113 526 2543

Footer

Contact Us

Turnkey Dental Supplies Ltd
Correspondence office:
15 Queen Square Leeds,
West Yorkshire, LS2 8AJ
Call: 07827 669302 or 0113 526 2543

ABOUT US

A family-run business with customer service very much at the heart of what we do. Design, build, install the very best Dental Surgeries… Learn More

Copyright © 2026 · Site by Many Hats Agency Ltd · WordPress · Log in

  • Home
  • About Us
  • Shop
  • Our Services
  • Case Studies
  • Product Brochures
  • Blog Posts
  • Contact Us